Max Growing Weed

[steamroller]

Bandit had a filter box that would fit a furnace type filter in it diagonally. From bottom corner to top corner.
It blocked light and all air had to go through the filter.
That is pretty slick there Max. Tool box on the down low.

 

[Max 2]

Yep ..the ol vents in the tool box trick haha..I did have filters on but they were restricting the airflow in as they were only rated at 270cfm ..my exhaust fan is 750 cfm .it was working on low but it was taking soo damn long to extract the warm air the rh was always climbing..soon as I took them off the room exhausted quicker and got the rh down..I need to find a bigger rated one but I have only made two 6 inch holes .need like 0ne big ten inch hole but I couldn’t find one big enough that had flaps but i spose I won’t need to now because no light won’t get into the room when exhaust fan comes on…

 

[Max 2]

First defol is done bar the biggun at the front.ran out of short stakes .i wanna just do the lowers and wait a little longer once stretch is about finished then throw some long stakes in…she’s a big girl.lifted up the middle one abit..fed and all tucked in for the nite..I didn’t want to go to town with the defol cause in 3-4 days they are going to start budding.left the top big fan leaves on a few .doesn’t look like I’ve done them to you guys but you should of seen them .no swinging room for Tarzan ..they will b loving that hair cut.
View attachment IMG_9921.MOV

 

[Max 2]

Start of day 11 ..the bud show has begun .going to prop the left side up to b on equal terms with the front plant.there’s 5 good sized plants in there.gonna b a good grow this one 22 1/2 to light 630ppm ph 6.0 air temp 26-26.5 rh 54-60..
View attachment IMG_9934.MOV

 

[steamroller]

Do you have a fan for down under?
That's a nice tight group there.

 

[Max 2]

No but I’ve been wanting to put one down low..what helps though is when the 2 in-line ducts open down bottom every minute and a half that brings in cold air for about 45 secs .

 

[Stoneyluv]

he said down under!!

 

[Max 2]

he said down under!!

he said down under!!

. In backward flushing land…

 

[steamroller]

At least Stoney saw what I did there~!

 

[Max 2]

Miss Danny is sure getting squeezed out in there lol....poor Danny .her sick friend is getting pushed out too .time to find her another home or end up on the green waste pile….getting crowded in there now as they are blowing up fast.i can move them sideways about 10 cm but that’s it.
Man it would of been soo crowded if Danny and the one in front of her grew like the others .i wouldn’t of grown them an extra week in veg if I did..maybe I only need to grow them 4 weeks to run 9 in there..there’s 5 big bitches in there .8 more days of stretch to go.i better stack up on finger blister cream time harvest comes lol.



View attachment IMG_9940.MOV

 

[Chemistry]

Go Danny you can make it.

 

[Max 2]

At least Stoney saw what I did there~!

stoney can’t b stoned right now

Are you me Steam

 

[Max 2]

Go Danny you can make it.

Danny’s deaf Chem .I’ve threatened her many times but she don’t give a shit .probably have enough on her to roll a couple joints.

I could give her the boot any time now.the back 2 would love that little bit of space.very tempted .lol

 

[Max 2]

God damn..these ph/ec pens are giving me the shits..thought I’d recalibrate the pen as when I mix a+b it says 720ppm after a quick stir.pull it out of nutes.put it back in and stir again just for a sec or two. Check…680ppm..do that a few more times it’s down to 600ppm .the reading should b stable not dropping..ph reading is solid..that doesn’t move..so I use an quick cal satchet to calibrate…wrong comes up and that means either change the solution or clean pen so I did both …used another satchet…same result so I try the 2 point calibration and select std cal on the pen..use the 7.0 first ..up come rec ,which means it recognises it .okay 1 comes up….cool.. do 4.0. Yep that works .okay 2 comes up..now for the ec..nope…wrong comes up…so I guess the ec probe is up the shit..it’s probably been like that right from the beginning as it was out 200 ppm when I calibrated it for the second time since I’ve had it….so in the space of 3 weeks I’ve calibrated it 3 times…well twice really cause the fucking thing won’t calibrate now…pen has always had storage solution in the cap so the pen probes should b pretty clean with only 3 weeks use..now I have to guess how much ppm I’m giving them till I have another meter.the cheapo ph pens gonna have to do the job till it’s fixed or they give me another.400 buck pen lol .ph is more important than nutes as I can just watch them..have a little tip burn which is why I wanted to recalibrate the pen..I was most likely giving them 720 ppm .